Frigidaire washer errors

Home » Frigidaire washer errors

Codes for the front Load virtual show fashions

Those mistakes code explanations can help you diagnose a problem with your Frigidaire the front-load washer with a virtual show built in 2014 and later. For restore how-to assist, visit the PartsDirect restore help section, which incorporates repair assist for washing machines, other important home equipment, garden and lawn system, storage door openers, vacuum cleaners and greater. you may additionally search for proprietor’s manuals and find washing gadget alternative elements.

test out our washer error code charts for information on a specific Frigidaire version or another brand of washer.

mistakes Code circumstance take a look at/repair shop elements
E11 Fill time too long
make certain that the water deliver taps behind the washing machine are completely open. take a look at for frozen fill lines in the wintry weather. Unplug the washing machine and disconnect the fill hoses from the again of the washer. test for correct water drift through the fill hoses. If water glide is insufficient, have a plumber restore the water deliver to the taps.

If water flows okay, check the inlet screens at the water inlet valve assembly. If the screens are clogged, update the water inlet valve meeting instead of cleaning the monitors (cleansing may want to allow particles to enter the valves, ensuing inside the valves sticking open and causing flooding).

take a look at the drain hose for proper set up. An improperly hooked up drain hose causes fill water to siphon out via the washer drain. also, test the drain pump for particles due to the fact objects including paper clips and cash can save you the washer from draining properly and allow fill water to siphon out via the washer drain.

If these recommendations don’t resolve the problem, the inlet water valve meeting probable needs to get replaced.

See the repair manual to repair it yourself Water inlet valve meeting
E13 Water leak inside the bath or air leak inside the water stage stress sensor air hose Drain the water out of the washing machine. Unplug the washer and take a look at the outer bathtub for cracks or leaks along with water dripping from the lowest of the washer bath or a hose. update the tub if leaking. in case you discover no water leaks, check the water degree strain sensor air hose for air leaks. replace the air hose if it leaks. If the hose doesn’t leak, replace the water level stress sensor as it’s now not detecting the water degree inside the washer.
Outer wash bath, water level strain sensor air hose, water degree strain sensor
E21 Drains slowly test your private home’s washer drain and the washer’s drain hose for clogs and clean any clogs located. Unplug the washer and take a look at the drain pump for a clog. If the drain direction is apparent, the drain pump commonly wishes changing.
See the repair manual to fix it your self Drain pump
E31 or E32 Water stage pressure sensor isn’t always communicating with the electronic control board Unplug the washer and check the twine harness connections between the water stage stress sensor and the control board. If the wiring connections are sound, you will commonly need to replace the water level strain sensor.
Water stage strain sensor
E35 Water level strain sensor detects overfill If the washer overfilled, unplug the strength wire and see if water maintains to fill the bath. if so, replace the water inlet valve assembly because a water valve isn’t always final. If the washer didn’t overfill, the water degree strain sensor commonly wishes changing.
See the restore guide to repair it yourself Water inlet valve assembly, water stage stress sensor
E38 Clogged air trap Unplug the washer and check the air lure and the water stage stress switch air hose for clogs. clear any clogs. If the air entice and air hose are clean, the water level strain sensor typically needs changing because it’s now not detecting the exchange in air stress as the tub fills.
Water level pressure sensor
E41 manage detects the door open Unplug the washer and test the wiring harness connections between the door lock meeting and the electronic control board. Reconnect any free wires or replace the twine harness if damaged. If the wire connections are okay, the door lock meeting normally needs replacing.
See the restore guide to restore it yourself wire harness, door lock meeting
E43, E45, E48 or E4A control detects a hassle with the door lock circuit Unplug the washer and take a look at the wiring harness connections between the door lock assembly and the digital control board. Reconnect any loose wires or update the wire harness if broken. If the twine connections are k, the door lock assembly generally wishes changing.
See the repair guide to fix it your self cord harness, door lock assembly
E47 control detects an open door lock circuit in spin mode Unplug the washer and test the wiring harness connections between the door lock assembly and the electronic manage board. Reconnect any unfastened wires or update the wire harness if broken. If the twine connections are okay, the door lock assembly normally needs replacing.
See the restore manual to fix it yourself twine harness, door lock meeting
E52 terrible sign from the power motor tachometer Unplug the washing machine and check the wire harness connections among the force motor and the motor control board. Reconnect any unfastened wires or replace the wire harness if broken. test the resistance through the tachometer at the force motor the usage of a multimeter. if you do not measure between 105 and 130 ohms, the tachometer is faulty and also you’ll need to update the force motor. The tachometer is built into the power motor and cannot get replaced one after the other. If tachometer resistance is ok, update the motor manage board.
See the repair manual to repair it your self twine harness, drive motor, motor manage board
E53 Low voltage to the motor manipulate board Unplug the washer and take a look at the twine harness among the electronic control board and motor manipulate board. Reconnect any unfastened wires or replace the harness if broken. If the wire harness is ok, the electronic control board generally wishes replacing.
See the repair manual to restore it yourself twine harness, digital manage board
E54 force motor over velocity Unplug the washer and take a look at the resistance through the tachometer at the force motor using a multimeter. in case you don’t measure among a hundred and five and 130 ohms, replace the power motor due to the fact the tachometer is defective. The tachometer is built into the pressure motor and can not get replaced one after the other. If tachometer resistance is k, update the motor control board.
power motor, motor manipulate board
E55 power motor beneath velocity Unplug the washing machine and take away the pressure belt. Spin the motor pulley. If it doesn’t spin freely, update the force motor. If the motor spins freely, rotate the huge pressure pulley at the returned of the washing machine bathtub to check the spin bearing. If the pulley would not spin freely, you will typically need to update the outer tub and spin basket because the spin bearing failed. If the motor pulley and power pulley both spin freely, then you may have a awful motor windings or a defective motor manage board.
See the restore manual to repair it yourself drive motor, outer bath, spin basket, motor manipulate board
E57 or E58 high contemporary on the pressure motor Unplug the washing machine and remove the drive belt. Spin the motor pulley. If it does not spin freely, update the drive motor. If the motor spins freely, rotate the massive power pulley at the back of the washing machine bath to test the spin bearing. If the pulley does not spin freely, you may normally want to replace the outer bath and spin basket due to the fact the spin bearing failed. If the motor pulley and force pulley both spin freely, then you can have a terrible motor windings or a defective motor manipulate board.
See the restore guide to fix it your self pressure motor, outer bath, spin basket, motor control board
E59 No tachometer sign for 3 seconds Unplug the washing machine and test the resistance thru the tachometer on the power motor the usage of a multimeter. in case you do not measure between 105 and 130 ohms, update the power motor because the tachometer is defective. If the tachometer resistance is ok, take away the drive belt. Spin the motor pulley. If it would not spin freely, update the pressure motor. If the motor spins freely, rotate the large pressure pulley at the back of the washing machine tub to test the spin bearing. If the pulley would not spin freely, you’ll normally need to update the outer tub and spin basket because the spin bearing failed. If the motor pulley and pressure pulley both spin freely, then you could have a terrible motor windings or a faulty motor manage board.
See the restore manual to repair it your self force motor, outer tub, spin basket, motor control board
E5A or E5C Motor manage board is overheated The motor control board is defective. Unplug the washer and update the motor control board.
See the restore manual to fix it yourself Motor manage board
E5D or E5F verbal exchange failure among the digital manage board and the motor manipulate board Unplug the washer and take a look at the wire harness connections between the main electronic manipulate board and the motor manage board. If the cord harness connections are okay, update the speed manage board. If the problem maintains, replace the main electronic manage board.
Motor control board, electronic manipulate board
E67 incorrect voltage deliver to the microprocessor on the digital manipulate board Unplug the washer for 5 minutes after which restore energy. If the code returns after restoring electricity, unplug the washing machine and replace the digital manage board.
digital manipulate board
E68 Heater failure Unplug the washing machine. Disconnect the heater and take a look at resistance the use of a multimeter. The heater have to degree approximately 14 ohms of resistance. update the heater in case you degree infinite resistance. take a look at for a brief within the heater to the steel cabinet. replace the heater if it is electrically shorted to the metallic cupboard. If the heater is okay, replace the digital manipulate board.
Heater, electronic manage board
E71 Heater temperature sensor blunders Unplug the washer and degree the resistance of the heater temperature sensor the use of a multimeter. It ought to degree around 4,800 ohms. If it doesn’t, update the heater. If it does, test the wiring connections among the heater temperature sensor and the digital manipulate board. Reconnect any free wires. update the cord harness if broken.
Heater, twine harness
E75 Failed water temperature sensor circuit Unplug the washer and test the resistance through the water temperature sensor circuit using a multimeter. You must measure around 50,000 ohms at room temperature. If resistance is off, you may want to replace the water inlet valve meeting because that meeting homes the water temperature sensor and the sensor isn’t available as a separate aspect. in case you degree accurate resistance through that circuit, update the electronic manipulate board due to the fact the control board isn’t detecting the appropriate resistance.
Water inlet valve, digital manage board
E91 or E92 communication hassle Unplug the washing machine and take a look at the twine harness connections among the electronic manage board and the consumer interface board. Reconnect any unfastened twine connections or update the twine harness if damaged. If the twine harness connections are k, update the consumer interface board. If the hassle maintains, replace the principle electronic manage board.
user interface board, digital manipulate board, twine harness
E93, E94, or E97 digital control board or person interface board failure Unplug the washing machine and check the cord harness connections among the electronic control board and the user interface board. Reconnect any loose twine connections or replace the cord harness if damaged. If the wire harness connections are okay, replace the consumer interface board. If the hassle maintains, update the principle digital manipulate board.
user interface board, electronic control board, wire harness
E98 or E9F Motor control communique hassle Unplug the washer and take a look at the wire harness connections among the electronic control board and the motor manipulate board. Reconnect any unfastened twine connections or update the cord harness if broken. If the wire harness connections are k, update the electronic manage board. If the problem keeps, update the motor manipulate board.
See the restore guide to restoration it yourself digital manage board, motor manipulate board, twine harness
EA1 Incoming strength frequency out of limits Unplug the washing machine and feature your nearby electrical power service company test the energy deliver frequency. If it’s everyday and the code does not clean, update the electronic control board.
digital manipulate board
EA2 energy supply voltage above a hundred thirty VAC Unplug the washing machine and take a look at the hole voltage with a multimeter. If the voltage is excessive, have an electrician restore the voltage supply hassle. If the voltage is everyday, update the electronic manage board.
digital manipulate board
EA3 power supply voltage decrease than a hundred VAC Unplug the washing machine and take a look at the opening voltage with a multimeter. If the voltage is low, have an electrician restore the voltage supply trouble. If the voltage is regular, replace the digital manage board.
digital manipulate board
EA5 primary voltage sensing failure Have the electricity agency check the frequency and voltage of the incoming strength supply. If accurate, replace the digital control board.
electronic control board
EAE Line secure relay sensing failure Have the strength organisation test the frequency and voltage of the incoming power supply. If correct, replace the digital control board.
digital control board
EF1 Clogged drain pump Unplug the washer and clear the clog from the drain pump. If the drain pump won’t pump water when it’s going for walks, replace it.
See the restore guide to restoration it yourself Drain pump
EF2 too much suds reduce the amount of high-performance (HE) detergent which you use.
HE detergent
EF6 manage reset Unplug the washing machine for five mins and then repair energy. If the code returns after restoring strength, unplug the washer and replace the electronic control board.
electronic manage board
EF8 stuck button loose the caught button. in case you cannot loose the caught button, unplug the washer and update the user interface board.
consumer interface board