πŸ“ Miami, Hialeah, Doral, Miami Lakes & More  | πŸ“ž (786) 587-0722  |  Mon–Sun 6:00 AM – 10:00 PM
Services
🌬️ Dryer Repair🫧 Washer Repair 🧊 Refrigerator Repair🍽️ Dishwasher Repair πŸ”₯ Oven & Stove RepairπŸ“‘ Microwave Repair πŸ—‘οΈ Garbage DisposalπŸ’¨ Dryer Vent Cleaning
Service Areas
πŸ“ AventuraπŸ“ Bal Harbour πŸ“ Bay Harbor IslandsπŸ“ Biscayne Park πŸ“ BrownsvilleπŸ“ Coral Gables πŸ“ Coral TerraceπŸ“ Country Club πŸ“ DoralπŸ“ El Portal πŸ“ FlagamiπŸ“ Fontainebleau πŸ“ GladeviewπŸ“ Golden Beach πŸ“ HialeahπŸ“ Hialeah Gardens πŸ“ Indian CreekπŸ“ Ives Estates πŸ“ KendallπŸ“ Key Biscayne πŸ“ MedleyπŸ“ Miami πŸ“ Miami BeachπŸ“ Miami Gardens πŸ“ Miami LakesπŸ“ Miami Shores πŸ“ Miami SpringsπŸ“ North Bay Village πŸ“ North MiamiπŸ“ North Miami Beach πŸ“ Opa-lockaπŸ“ Palmetto Bay πŸ“ PinecrestπŸ“ South Miami πŸ“ Sunny Isles BeachπŸ“ Surfside πŸ“ SweetwaterπŸ“ Virginia Gardens πŸ“ Westchester
Brands
🏷️ Amana🏷️ Bosch 🏷️ Electrolux🏷️ Fisher & Paykel 🏷️ Frigidaire🏷️ GE 🏷️ Kenmore🏷️ KitchenAid 🏷️ LG🏷️ Maytag 🏷️ Miele🏷️ Samsung 🏷️ Sub-Zero🏷️ Thermador 🏷️ Viking🏷️ Whirlpool 🏷️ Wolf
⚑ Error CodesπŸ“ Blog ❓ FAQ🏠 Aboutβœ‰οΈ Contact
πŸ“ž Call (786) 587-0722

Admiral Washer Error Codes

Complete fault code reference for Admiral washers. Each code includes probable causes and verified diagnostic steps based on manufacturer service documentation.

πŸ“‹ 6 Fault Codes
🫧 Admiral Washer
πŸ“ž Same-Day Service Available

Found Your Error Code?

Our technicians serve Miami, Hialeah, Doral, and surrounding areas β€” same day. Call now for fast diagnosis and repair.

πŸ“ž Call (786) 587-0722
πŸ“‹ Error Code Index β€” Admiral Washer
F01
Main Control Board Failure
Main electronic control board has detected an internal fault and cannot continue operating.
High Priority
Possible Causes
  • Control board component failure due to age or heat
  • Power surge damage to board circuitry
Diagnostic Steps
  1. 1Disconnect power for 60 seconds and retry
  2. 2Inspect board for visible burn marks or damage
  3. 3Replace main control board if fault persists
F11
Serial Communication Error
Communication fault between main control board and motor control board.
High Priority
Possible Causes
  • Wiring harness connection loose between boards
  • Motor control board failed
  • Main control board failed
Diagnostic Steps
  1. 1Check wiring harness connections at both control boards
  2. 2Power cycle unit 60 seconds
  3. 3Replace motor control board or main board as indicated by testing
F21
Long Drain Time
Appliance did not drain within the allowed time limit β€” water remaining in drum.
Medium Priority
Possible Causes
  • Drain pump filter blocked with debris β€” most common cause
  • Drain hose kinked or improperly routed
  • Drain pump motor failed
Diagnostic Steps
  1. 1Clean drain pump filter β€” remove all lint, coins, and debris
  2. 2Check drain hose for kinks and proper routing to house drain
  3. 3Test drain pump motor continuity and replace if failed
F35
Analog Pressure Sensor Failure
Water level analog pressure sensor reading outside expected range β€” water level cannot be verified.
Medium Priority
Possible Causes
  • Pressure sensor failed internally
  • Pressure hose kinked or disconnected from sensor port
  • Air dome on tub blocked with detergent residue
Diagnostic Steps
  1. 1Check pressure hose connection at sensor and at tub air dome
  2. 2Clear any blockage from air dome port on tub
  3. 3Test pressure sensor and replace if reading is out of range
F51
Motor RPS Failure
Rotor position sensor not providing signal to motor control board β€” motor speed cannot be monitored.
Medium Priority
Possible Causes
  • RPS sensor failed internally
  • Wiring to RPS sensor open or shorted
  • Motor control board fault
Diagnostic Steps
  1. 1Check RPS sensor wiring harness for damage or loose connection
  2. 2Test RPS sensor resistance per service manual specifications
  3. 3Replace RPS sensor if reading is out of specification
SUD
Excess Suds Detected
Excessive suds detected in drum β€” cycle paused to allow suds to dissipate before continuing.
Low Priority
Possible Causes
  • Non-HE (high-efficiency) detergent used in HE washer
  • Too much HE detergent used per load
  • Detergent residue buildup in dispenser drawer
Diagnostic Steps
  1. 1Use only HE-rated detergent β€” check package for HE symbol
  2. 2Reduce detergent quantity β€” less is more in HE machines
  3. 3Run a Rinse & Spin cycle to clear remaining suds
  4. 4Clean detergent dispenser drawer regularly

Need a Technician in Miami or Hialeah?

AppliancesCare provides same-day Admiral washer repair across Miami-Dade. Bilingual service β€” English & Spanish.

πŸ“ž Call (786) 587-0722

Important Notice: Washer error code information on this page is based on manufacturer service documentation. Always disconnect power and water supply before inspecting internal components. Fault behavior and diagnostic steps may vary by model and production date. When in doubt, contact a certified appliance technician. AppliancesCare Appliance Repair LLC provides this information for educational purposes only.