πŸ“ Miami, Hialeah, Doral, Miami Lakes & More  | πŸ“ž (786) 587-0722  |  Mon–Sun 6:00 AM – 10:00 PM
Services
🌬️ Dryer Repair🫧 Washer Repair 🧊 Refrigerator Repair🍽️ Dishwasher Repair πŸ”₯ Oven & Stove RepairπŸ“‘ Microwave Repair πŸ—‘οΈ Garbage DisposalπŸ’¨ Dryer Vent Cleaning
Service Areas
πŸ“ AventuraπŸ“ Bal Harbour πŸ“ Bay Harbor IslandsπŸ“ Biscayne Park πŸ“ BrownsvilleπŸ“ Coral Gables πŸ“ Coral TerraceπŸ“ Country Club πŸ“ DoralπŸ“ El Portal πŸ“ FlagamiπŸ“ Fontainebleau πŸ“ GladeviewπŸ“ Golden Beach πŸ“ HialeahπŸ“ Hialeah Gardens πŸ“ Indian CreekπŸ“ Ives Estates πŸ“ KendallπŸ“ Key Biscayne πŸ“ MedleyπŸ“ Miami πŸ“ Miami BeachπŸ“ Miami Gardens πŸ“ Miami LakesπŸ“ Miami Shores πŸ“ Miami SpringsπŸ“ North Bay Village πŸ“ North MiamiπŸ“ North Miami Beach πŸ“ Opa-lockaπŸ“ Palmetto Bay πŸ“ PinecrestπŸ“ South Miami πŸ“ Sunny Isles BeachπŸ“ Surfside πŸ“ SweetwaterπŸ“ Virginia Gardens πŸ“ Westchester
Brands
🏷️ Amana🏷️ Bosch 🏷️ Electrolux🏷️ Fisher & Paykel 🏷️ Frigidaire🏷️ GE 🏷️ Kenmore🏷️ KitchenAid 🏷️ LG🏷️ Maytag 🏷️ Miele🏷️ Samsung 🏷️ Sub-Zero🏷️ Thermador 🏷️ Viking🏷️ Whirlpool 🏷️ Wolf
⚑ Error CodesπŸ“ Blog ❓ FAQ🏠 Aboutβœ‰οΈ Contact
πŸ“ž Call (786) 587-0722

Samsung Dryer Error Codes

Complete fault code reference for Samsung dryers. Each code includes probable causes and verified diagnostic steps based on manufacturer service documentation.

πŸ“‹ 8 Fault Codes
🌬️ Samsung Dryer
πŸ“ž Same-Day Service Available

Found Your Error Code?

Our technicians serve Miami, Hialeah, Doral, and surrounding areas β€” same day. Call now for fast diagnosis and repair.

πŸ“ž Call (786) 587-0722
πŸ“‹ Error Code Index β€” Samsung Dryer
AE7
Wireless Communication Fault
Wi-Fi or SmartThings communication module fault detected.
Low Priority
Possible Causes
  • Wi-Fi router signal lost
  • SmartThings app connection timeout
  • Communication module firmware issue
Diagnostic Steps
  1. 1Check Wi-Fi router connection
  2. 2Reconnect appliance to SmartThings app
  3. 3Power cycle dryer β€” may restore connection
bE3
Button Stuck
A button on the control panel is continuously activated.
Medium Priority
Possible Causes
  • Moisture on control panel causing false activation
  • Physical damage to button
  • Debris under button surface
Diagnostic Steps
  1. 1Dry control panel area with clean cloth
  2. 2Press all buttons to free stuck button
  3. 3Replace control panel if fault persists
Et
Temperature Sensor Fault
Drum temperature sensor open or out of expected range.
Medium Priority
Possible Causes
  • Temperature sensor failed open or shorted
  • Connector loose or corroded
Diagnostic Steps
  1. 1Inspect sensor connector for corrosion
  2. 2Test sensor resistance β€” should vary with temperature
  3. 3Replace temperature sensor if reading is OL or near zero
FC
Vent Blockage β€” Airflow Restricted
Dryer detecting restricted airflow through exhaust system.
High Priority
Possible Causes
  • Lint screen clogged with buildup
  • Exhaust vent duct blocked or kinked
  • Exterior vent flap stuck closed
Diagnostic Steps
  1. 1Clean lint screen thoroughly
  2. 2Inspect full exhaust duct run for blockage
  3. 3Check exterior vent flap opens freely during operation
HE
Overheating
Drum temperature exceeded maximum safe limit.
Urgent
Possible Causes
  • Exhaust vent blocked β€” restricted airflow
  • Thermostat failed closed
  • Temperature sensor providing incorrect reading
Diagnostic Steps
  1. 1Stop dryer immediately
  2. 2Clean lint screen and inspect full exhaust duct
  3. 3Test thermostat and temperature sensor
tE1
Thermistor 1 Fault (Exhaust)
Exhaust air thermistor 1 open or out of expected range.
Medium Priority
Possible Causes
  • Thermistor failed open or shorted
  • Connector loose or corroded
Diagnostic Steps
  1. 1Inspect connector for corrosion
  2. 2Test thermistor resistance β€” should decrease as temp rises
  3. 3Replace thermistor 1 if reading is OL or near zero
tE2
Thermistor 2 Fault (Drum)
Drum air thermistor 2 open or out of expected range.
Medium Priority
Possible Causes
  • Thermistor failed open or shorted
  • Connector loose or corroded
Diagnostic Steps
  1. 1Inspect connector for corrosion
  2. 2Test thermistor resistance
  3. 3Replace thermistor 2 if reading is OL or near zero
tE3
Thermistor 3 Fault (Inlet)
Inlet air thermistor 3 open or out of expected range.
Medium Priority
Possible Causes
  • Thermistor failed open or shorted
  • Connector loose or corroded
Diagnostic Steps
  1. 1Inspect connector for corrosion
  2. 2Test thermistor resistance
  3. 3Replace thermistor 3 if reading is OL or near zero

Need a Technician in Miami or Hialeah?

AppliancesCare provides same-day Samsung dryer repair across Miami-Dade. Bilingual service β€” English & Spanish.

πŸ“ž Call (786) 587-0722

Important Notice: Error code information on this page is based on Samsung manufacturer service documentation. Dryer repair involves high-voltage components and hot surfaces. Always disconnect power before servicing. AppliancesCare Appliance Repair LLC provides this information for educational purposes only.